Ask Slashdot: Dealing With Electrostatic Contamination? 197
interval1066 writes "I've generally made it a practice to blow the dust out of my devices 1) when I remember to do so 2) after about 3 or so years of use 3) when I can get inside the case. My monitor is very thin and difficult to open. When I did finally crack it open I didn't really notice a whole lot of dust, but I blew the thing out anyway and put it back together, and it's doing ok, as far as I can tell. I'd be interested in knowing other Slashdotters' experiences with maintaining their devices in this way and where possible. And I actually extending the life of my devices, or am I just wasting my time?"
Re:Teflon tap (Score:3, Informative)
Trolling aside, I've found that the best way to clean those ISA/PCI/AGP connectors is a white "STAEDTLER" eraser.
Do you want maintainability, or convenience? (Score:5, Informative)
There's a tradeoff between lifespan and maintenance requirements. For fun, I restore old Teletype machines from the 1920s and 1930s. I have four of them running.
A normal maintenance operation on early Teletypes is to remove the two electrical parts (the motor and the selector magnet) and soak the entire machine in cleaning solution to get rid of dust and dead oil. For machines in heavy use, Western Union did that annually. Then they had to be oiled again (there are several hundred oiling points and six pages of lubrication instructions), gears and sliding joints greased, the electrical parts re-installed, adjustment procedures performed, and the machines re-tested.
Because of this design for maintainability, I've been able to take 80 year old machines that were covered with rust and dirt, and restore them to full operation. But who would put up with something today which required that kind of maintenance? Getting people to clean or change the filters on their desktop computers is difficult.
Re:Not your time, ALL OUR TIME (Score:3, Informative)
With a headline of "dealing with electrostatic contamination" I was prepared for something along the lines of someone who has issues of constantly discharging static electricity, perhaps affecting a DIY clean room they're building or their workplace. Instead it's a fucking question about dust in a computer.
If it's not broken, don't fix it. (Score:4, Informative)
That's a golden rule.
Most consumer equipment does not need or tolerate frequent maintenance. Cracking open an LCD monitor is not going to make it last longer, on the contrary, you are putting stress on plastic tabs (specially if it doesn't have screws), and on marginal quality harnesses and connectors that are meant to be assembled once.
Depends. (Score:5, Informative)
If you're cleaning them correctly and carefully, you'll extend their lives. Dust buildup is a leading cause of overheating in PCs, and heat is a real problem.
But if you're cleaning them incorrectly, you'll shorten their lives. Any time you open the case, you're exposing sensitive components to risk, especially static damage. Not grounding yourself to the case when you're touching internal components will allow any static buildup on your body to discharge through a component. Vacuum cleaners draw so much air through them that they generate static electricity, particularly on the tip of a plastic nozzle. Static discharges at lower voltages are invisible and can cause latent damage that you may not immediately discover, but those weaknesses enable other normal stresses to destroy the chip.
When you take it apart to clean it, you're exposing it to non-zero risk. You might make a mechanical mistake in assembly that impacts proper cooling. You might put the CPU heatsink on cockeyed, fail to equally tension all the heat sink mounting screws, or drape a stray cable across a fan and prevent it from turning. Failing to put airflow devices back in their correct place, or failing to reconnect the fans to the power cables, could reduce needed airflow. When you carry it to the workbench, you risk dropping it. I've seen people reuse old thermal paste or glob on a thick layer of new paste when replacing the CPU fan (the fan maker's pre-paste is usually horribly thick.) A bad thermal paste layer will insulate the CPU from the heat sink and cause overheating. Lots of the aftermarket CPU fans have really weird mounting hardware, and you need to be sure they're correctly mounted so they effectively transfer the heat. All these risks can be reduced by learning how to do it right, reading the directions, and taking appropriate precautions.
One way to greatly reduce the risk of damage due to improper handling is to clean the machines only as often as necessary. Dust buildup is dependent on your particular environment. Fabrics, pets, dirt, open windows, flowering plants, carpeting, low humidity, high humidity, smoke, grease, cooking oils, hair sprays, colognes, all are factors that contribute to the build up of dust. So clean it after a year, and figure out what the cleaning schedule should be based on what you discover. It might be that annual cleanings are appropriate, or maybe you can wait two or three years.
All heat is a problem. Direct thermal damage from too much heat is possible, of course, but temperature changes can cause problems too. Thermal expansion causes the mechanical motion of parts. Every material has a different coefficient of expansion, (e.g. aluminum expands more per degree than steel, plastic expands more than aluminum,) so as parts heat and cool, they tug at solder connections, screw mountings, and other interface points inside the case. Repeated heating and cooling cycles increase the possibility of damage. Keeping it clean will keep it cooler, reducing the amount of expansion and motion, and extending the life.
Note that I'm not saying you'll ever drop your computer or ever reassemble it incorrectly, I'm pointing out that the act of cleaning it creates a risk greater than zero, and that the risk is zero when you are not cleaning it. And bigger risks lead to shorter lifespans.
Re:For the most part (Score:0, Informative)
defiantly? Really? And don't tell me it's a typo, beceause you used it twice.
The word is definitely. Just because your spellcheck don't flash doesn't mean you spelled everything correctly.
Dishwasher used for cleaning old PDP-11 cards (Score:4, Informative)